Epics@GSI Webhome

HadCon 2

Introduction

HadCon2 is a credit-card sized general purpose I/O module for detector and experiment controls as well as for small data acquisition systems.

hadcon2

It is the successor of the discontinued first version HadCon ( HADControl/HadShoPoMo general purpose board, HadCon @ Epics Wiki).

The module has an ATMEL AT90CAN128 microcontroller providing a multitude of connectivity:
I2C (8/4 fold (intern/extern) multiplexer), 6 channel 1-wire master, 8-channel 8bit DAC, galvanically isolated CAN - high-speed transceiver, 8-channel 10-bit SAR ADC, byte-oriented SPI, in total up-to 53 programmable I/O lines and optionally a Lattice MachX02 FPGA for fast data processing tasks.

While the discontinued precursor HadCon had an SoC on-board, its successor HadCon2 has broken up this concept in favour of a more open access:
It doesn't have any CPU on board, but a USB connector to directly allow communication with any type and size of computer (e.g. PC, raspberry PI, dreamplug, ...) having an USB port on one side and at the other end the microcontroller and the FGPA. This communication is based on an ASCII-based protocol in view of easy implementation in detector control systems like e.g. EPICS and LabVIEW.

  • Summarizing:
    • Microcontroller: ATMEL AT90CAN128
      • I2C
      • CANbus
      • SPI
      • ADCs
      • ...
    • FPGA: Lattice MachX02-1200-HC
    • FTDI USB to serial UART interface
      • USB 2.0 connector
      • Power over USB
    • I2C devices
      • 6 × Single-Channel 1-Wire Master
      • 1 × 8-channel I2C-bus multiplexer with reset
      • 2 × 4-channel 8-Bit DAC - Digital-to-Analog Converter
    • galvanically isolated CAN - High-speed CAN Transceiver
      • optional external power supply
    • 2 × Rotary Code Switches, hexadecimal coding
    • Reset Button for ATMEL
    • 11 × LED's, free programmable


Documentation

Layout

Microcontroller ATMEL

FPGA

FTDI USB to serial UART interface

USART - Universal Synchronous and Asynchronous serial Receiver and Transmitter

  connects to
USART0 FTDI (USB)
USART1 FPGA

I2C

1 × 8-channel I2C-bus multiplexer with reset

  • pdf PCA9547, local copy
    • ATMEL's SDA/SCLsignals are multiplexed to up-to 8 lines.
      Multiplexer outDeviceSignals
      ATMEL's SDA/SCL SD0/SC0 DAC1: 4-channel DAC (DAC5574) DACOUT1 ... DACOUT3
      DAC2: 4-channel DAC (DAC5574) DACOUT4 ... DACOUT7
      SD1/SC1, SDA1 / SCL1 Connector JDI2C1
      SD2/SC2, SDA2 / SCL2
      SD3/SC3, SDA3 / SCL3
      SD4/SC4, SDA4 / SCL4
      SD5/SC5 2 × Single-Channel 1-Wire Master OWIO0 ... OWIO1
      SD6/SC6 2 × Single-Channel 1-Wire Master OWIO2 ... OWIO3
      SD7/SC7 2 × Single-Channel 1-Wire Master OWIO4 ... OWIO5
    • Addressing:
      DeviceI2C sub addressSignals
      A2A1A0
      U2: 8-channel I2C-bus multiplexer 0 0 0 OWIO0
  • The configuration can be set via I2C.
    • Device Addressing: (from manual)
      0b1110sssd, s:hardware selectable, d:direction R/\\bar(W)
    • Channel Select via Control Register:
    • Table 4. Control register
      0 0 0 0 1 0 0 0 channel 0 enabled; power-up/reset default state
      D7 D6 D5 D4 B3 B2 B1 B0 Command
      Write = channel selection; Read = channel status
      X X X X 0 X X X no channel selected
      X X X X 1 0 0 0 channel 0 enabled
      X X X X 1 0 0 1 channel 1 enabled
      X X X X 1 0 1 0 channel 2 enabled
      X X X X 1 0 1 1 channel 3 enabled
      X X X X 1 1 0 0 channel 4 enabled
      X X X X 1 1 0 1 channel 5 enabled
      X X X X 1 1 1 0 channel 6 enabled
      X X X X 1 1 1 1 channel 7 enabled
  • Connected to ATMEL's pin PB5 (OC1A) [...] pulling the RESET pin LOW resets the I2C -bus state machine causing all the channels to be deselected, except Channel 0 so that the master can regain control of the bus (from the manual].

6 × Single-Channel 1-Wire Master

  • pdf I2C-to-1-Wire® bridge device DS2482-101, local copy
  • Features:
    slew-rate control
    "To optimize 1-Wire waveform generation, the DS2482-101 performs slew-rate control on rising and falling 1-Wire edges and provides additional programmable features to match drive characteristics to the 1-Wire slave environment."
    pullup features
    "Programmable, strong pullup features support 1-Wire power delivery to 1-Wire devices such as EEPROMs and sensors."
  • Addressing:

Device I2C sub address Signals
A1 A0
U3: Single-Channel 1-Wire Master 1 0 OWIO0
U6: Single-Channel 1-Wire Master 1 1 OWIO1
U4: Single-Channel 1-Wire Master 1 0 OWIO2
U7: Single-Channel 1-Wire Master 1 1 OWIO3
U5: Single-Channel 1-Wire Master 1 0 OWIO4
U8: Single-Channel 1-Wire Master 1 1 OWIO5

2 × 4-channel 8-Bit DAC - Digital-to-Analog Converter

Device I2C sub address Signals
A1 A0
UDAC1: 4-channel DAC (DAC5574) 1 0 DACOUT1 ... DACOUT3
UDAC2: 4-channel DAC (DAC5574) 0 0 DACOUT4 ... DACOUT7

galvanically isolated CAN-bus

Can - High-speed Can Transceiver

iCoupler Digital Isolator

decoupling ATMEL's JTAG from ADC input

8-bit noninverting translator

Switches

Rotary Code Switches, hexadecimal coding

SWITCH1 Connector Pins AT90CAN128 via 4.7kΩ   SWITCH2 Connector Pins AT90CAN128 via 4.7kΩ
1 PC0 (A8) 1 PC4 (A12)
2 PC1 (A9) 2 PC5 (A13)
4 PC2 (A10) 4 PC6 (A14)
8 PC3 (A11) 8 PC7 (A15/CLK0)

Reset Button

  • KMR223 ITT micro miniature switch
  • pulls up ATMEL's RESET (pin20) to 3.3V via 10kΩ

Power

Input

Powering via
  • micro USB JUSB1 connector, or
  • jack DCPower

Output

GND Can be found on several Connectors
5,0V JCAN2 pin 4
3,3V JCAN2 pin 6

LEDs

leds.png

  pin color logic
AT90CAN128 PG0 ( WR ) red inverse logic:
0: on 1: off
PG1 ( RD ) yellow
PG2 (ALE) orange
MachX02 PT17D "DONE" red  
PL4A yellow  
PL4B orange  
PL4C yellow  
PL4D orange  
PL5A red  
PL5B yellow  
PL5C orange  

Connectors

JDINOUT1 / JDINOUT2

  • I/O of ATMEL

JDINOUT1 Connector Pins AT90CAN128   JDINOUT2 Connector Pins AT90CAN128
1 PA0 (AD0) 1 PC0 (A8)
2 PA1 (AD1) 2 PC1 (A9)
3 PA2 (AD2) 3 PC2 (A10)
4 PA3 (AD3) 4 PC3 (A11)
5 PA4 (AD4) 5 PC4 (A12)
6 PA5 (AD5) 6 PC5 (A13)
7 PA6 (AD6) 7 PC6 (A14)
8 PA7 (AD7) 8 PC7 (A15/CLK0)
9/10 GND 9/10 GND

JADC1

  • ADC inputs of ATMEL

Connector Pins AT90CAN128 comments
1 PF0 (ADC0)  
2 PF1 (ADC1)
3 PF2 (ADC2)
4 PF3 (ADC3)

5 PF4 (ADC4) overlap with JTAG inputs of ATMEL, can be decoupled by pulling TOSC2 low
6 PF5 (ADC5)
7 PF6 (ADC6)
8 PF7 (ADC7)

9/10 GND

JAtmelMISC1

  • ATMEL miscellaneous I/O, SPI

Connector Pins AT90CAN128 comments
1 PD2 (RXD1/INT2) USART1 RXD to connection to MachX02 or External Interrupt 2 Input
2 PD1 (TXD1/INT3) USART1 TXD to connection to MachX02 or External Interrupt 3 Input
3 PB0 ( SS ) Serial Peripheral Interface – SPI
4 PB1 (SCK)
5 PB2 (MOSI)
6 PB3 (MISO)
7 PE6 (T3/INT6) Timer/Counter3 Clock Input or External Interrupt 6 Input
8 PE7 (ICP3/INT7) Timer/Counter3 Input Capture Trigger or External Interrupt 7 Input

9/10 GND

JTAG1

  • JTAG connector

Connector Pins Signal comments
1 TCK 10kΩ to V3_3
2 GND  
3 TDO ← FPGA / Jumper J1 ← ATMEL
4 V3_3  
5 TMS  
6   not connected
7 V3_3  
8   not connected
9 TDI → ATMEL (→ FPGA)
10 GND  

JCAN1 / JCAN2

  • JCAN1 basic CAN connector

JCAN1 Connector Pins Signal comments
1 CANL ↔ CAN - High-speed Can Transceiver ATA6660 ↔ iCoupler Digital Isolator ↔ ATMEL
2 CANH
3/5 VCAN_INPUT
4/6 GND_CAN

  • JCAN2 provides optional CAN power supply,
    needs a jumper/cable/connection
    • between pin 1, GND_CAN and pins 3/5 for common GND
    • between pin 2, VCAN and pins 4 for 5,0V or
    • between pin 2, VCAN and pins 6 for 3,3V

JCAN2 Connector Pins Signal
1 GND_CAN
2 VCAN
4 V5_0
6 V3_3
3/5 GND_CAN

JMXOIO1 / JMXOIO2

  • LVDS I/O of FPGA MachX02

JMXOIO1 Connector Pins MachX02   JMXOIO2 Connector Pins MachX02
1/2 PT9A/B 1/2 PT15A/B
3/4 PT10A/B 3/4 PT16A/B
5/6 PT11A/B 5/6 PT16C/D
7/8 PT12A/B 7/8 PT17A/B
9/10 GND 9/10 GND

JDI2C1

  • 4 of 8 channel output of ATMEL's single I2C bus multiplexed by an 8-channel I2C multiplexer PCA9547 (q.v. above)

Connector Pins Multiplexer out task comment
1/2 SD1/SC1 SDA1 / SCL1 ATMEL's
multiplexed
SDA/SCL
3/4 SD2/SC2 SDA2 / SCL2
5/6 SD3/SC3 SDA3 / SCL3
7/8 SD4/SC4 SDA4 / SCL4
9/10 GND  

JDAC1

  • Output of the 2 4-channel DAC (DAC5574)

Connector Pins Signal Device Device pin
1 DACOUT0 UDAC1 VoutA
2 DACOUT1 VoutB
3 DACOUT2 VoutC
4 DACOUT3 VoutD
5 DACOUT4 UDAC2 VoutA
6 DACOUT5 VoutB
7 DACOUT6 VoutC
8 DACOUT7 VoutD
9/10 GND

JOWIO1

  • 1-wire connector for 6 channels provided by the 6 I2C driven Single-Channel 1-Wire Master DS2482
Connector Pins Signal
1 OWIO0
2 OWIO1
3 OWIO2
4 OWIO3
5 OWIO4
6 OWIO5
7/8 V3_3
9/10 GND

Bugs, Notes, Remarks, Tweaks & Twiddling

Notes and Remarks

1-wire

  1. When driving 1-wire devices, typically via JOWIO1, make sure to have (at least) 1 pull-up resistor of about 3.3kΩ on the data line of the 1-wire bus connected to the power VDD.
    • Recommended to have it at the master, e.g. at HadCon 's connector JOWIO1,.
    • Possible option for future, directly at the connector, when using one of JDINOUT2'spins as permanent power pin.

    • Since Single-Channel 1-Wire Master DS2482 is used at JOWIO1, this isn't necessary anymore, but keep in mind for other applications.

Tweaks / Bugfix

template 1
description
Therefore Action: i.e.
  1. pin 5 of UFF2 has to be disconnected from its pad and removed
  2. A cable has to be soldered connecting pin 1 of UFF2 to the solder pad of pin 5
template 2
description
Therefore Action: i.e.
  1. pin 5 of UFF2 has to be disconnected from its pad and removed
  2. A cable has to be soldered connecting pin 1 of UFF2 to the solder pad of pin 5


Firmware

Cables

Bookkeeping / Organization


-- PeterZumbruch - 2020-07-31
Topic revision: r16 - 2020-07-31, PeterZumbruch - This page was cached on 2024-12-07 - 18:34.

This site is powered by FoswikiCopyright © by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding GSI Wiki? Send feedback | Legal notice | Privacy Policy (german)