Event Numbers

Overview

Event numbers serve as IDs for actions performed by the control system.

Existing Facility

Information about event numbers used by the existing facility can be found here.

"New" FAIR Style Control System

The table below lists all event numbers. Please be aware of the following ranges for event numbers.

• 000..0255: exclusively used for MIL based timing. If event numbers in this range are distributed by the GMT, the corresponding timing messages will be processed by the relevant GMT->MIL gateway.
• 256..3999: exclusively used for the White Rabbit based General Machine Timing system.
• 4000..4095: reserved for internal use by the GMT.

Event Numbers Used for Operation

0dEvtNo	0xEvtNo	EvtName	Description	FESA relevance
0	0	EVT_PZ_ChanEnd	SIS/ESR PZ only: mark end of channel	N
1	1	EVT_START_RF	Power to RF cavities	Y
2	2	EVT_START_IQ	Begin of beam production	Y
3	3	EVT_IQ_HEATING	Begin of ion source arc, ECR RF	Y
4	4	EVT_PREP_BEAM_ON	Switch on chopper, read act. values	Y
5	5	EVT_IQ_GAS_ON	Start of heading gas (ion source)	Y
6	6	EVT_BEAM_ON	Valid beam	Y
8	8	EVT_BEAM_OFF	End of beam production	Y
10	A	EVT_STOP_IQ	Switch IQ off	Y
12	C	EVT_STOP_RF	Switch RF off	Y
16	10	EVT_PREP_NEXT_ACC	Prepare next acc., write set values	Y
17	11	EVT_AUX_PRP_NXT_ACC	Set values in magnet prep. cycles	N
18	12	EVT_RF_PREP_NXT_ACC	Begin of RF extra cycle	Y
19	13	EVT_PREP_UNI_DIAG	Prepare diagnostic devices, Unilac	N
20	14	EVT_PREP_AUX	Trigger BIF beam diagnostics	Y
21	15	EVT_UNLOCK_ALVAREZ	Unlock A4 for next pulse	N
22	16	EVT_PREP_EXP	Pretrigger for Experiments	Y
24	18	EVT_RF_AUX_TRIG	Trigger ADC in RF extra cycles	Y
25	19	EVT_MAGN_DOWN	Set magnets to zero current	Y
26	1A	EVT_SD_AUX_START	Beam diagnostics aux start trigger	Y
27	1B	EVT_SD_AUX_STOP	Beam diagnostics aux stop trigger	Y
28	1C	EVT_PRETRIG_BEAM	Magnets on flattop, PG trigger	Y
29	1D	EVT_UNI_END_CYCLE	End of a UNILAC cycle	N
30	1E	EVT_READY_TO_SIS	10 ms before beam transfer	N
31	1F	EVT_SRC_DST_ID	Source/Destination of beam	N
32	20	EVT_START_CYCLE	First Event in a cycle	N
33	21	EVT_START_BFELD	Start of B-Field	N
34	22	EVT_PEAK_UP	Peaking trip up	N
35	23	EVT_INJECT	B-field reached injection level	Y
36	24	EVT_UNI_TRANS	Demand UNILAC beam	N
37	25	EVT_UNI_ACKN	Acknowledge from Unilac	N
38	26	EVT_UNI_READY	Unilac ready, transfer in preparation	N
39	27	EVT_MB_LOAD	Start Bumper magnet ramp up	Y
40	28	EVT_MB_TRIGGER	Start active Bumper Ramp (down)	Y
41	29	EVT_INJECT_END	Start of injection from unilac	Y
42	2A	EVT_TIMEOUT_1	Trigger timeout channel 1	N
43	2B	EVT_RAMP_START	Start of acc/deacc ramp in magnets	Y
44	2C	EVT_PREP_INJ	Prepare devices for next Injection	Y
45	2D	EVT_FLATTOP	Magnets reached Flattop	Y
46	2E	EVT_EXTR_START_SLOW	Start of extraction	Y
47	2F	EVT_MK_LOAD_1	Load Kicker for HF-triggered puls	Y
48	30	EVT_MK_LOAD_2	Load Kicker for Timinggenerator-triggered puls	Y
49	31	EVT_KICK_START_1	Start Kicker for HF-triggered extraction	Y
50	32	EVT_TIMEOUT_2	Trigger timeout channel 2	N
51	33	EVT_EXTR_END	End of extraction	Y
52	34	EVT_FLATTOP_END	End of Flattop (Magnets) reached	Y
53	35	EVT_PREP_EXTR	Prepare devices for next Extraction	Y
54	36	EVT_PEAK_DOWN	Peaking strip down	N
55	37	EVT_END_CYCLE	End of a cycle	N
56	38	EVT_SYNCH	Trigger all function generators	Y
57	39	EVT_EXTR_BUMP	Start of closed orbit distortion	Y
58	3A	EVT_SIS_ACK_TO_ESR	SIS acknowledge to ESR	N
59	3B	EVT_SIS_READY_1	SIS ready for extraction to ESR	N
60	3C	EVT_SIS_READY_2	SIS ready for extraction to ESR	N
61	3D	EVT_TRANS_START_1	Begin of transmission to ESR	N
62	3E	EVT_TRANS_START_2	Begin of transmission to ESR	N
63	3F	EVT_PHASE_SYNCH_GATE_1	Begin of first phase synchronisation between ESR- and SIS-HF	N
64	40	EVT_TIMEOUT_3	Trigger timeout channel 3	N
65	41	EVT_PHASE_SYNCH_GATE_2	Begin of second phase synchronisation between ESR- and SIS-HF	N
66	42	EVT_TIMEOUT_4	Trigger timeout channel 4	N
67	43	EVT_TIMEOUT_5	Trigger timeout channel 5	N
68	44	EVT_TIMEOUT_6	Trigger timeout channel 6	N
69	45	EVT_KICK_START_2	Start Kicker for TG-triggered extraction	Y
70	46	EVT_UNI_PREP	Demand setting of TK (200 ms before beam)	N
71	47	EVT_INJ_BUMP	Closed orbit destortion for reinjection	Y
72	48	EVT_RE_INJ_START	SIS is ready for reinjection	N
73	49	EVT_RE_INJ_END	End of reinjection	N
74	4A	EVT_PREP_RE_INJ	Prepare devices for Reinjection	N
75	4B	EVT_PREP_KICK_1	Prepare kicker: load capacitor 1	Y
76	4C	EVT_PREP_KICK_2	Prepare kicker: load capacitor 2	Y
77	4D	EVT_MK_LOAD_RE_INJ	Load Kicker for Reinjection	N
78	4E	EVT_EXTR_STOP_SLOW	End of slow extraction	Y
79	4F	EVT_ASYNC_TRANS	Transfer to ESR without HF synchron.	Y
80	50	EVT_EMA_START	Start EMA meassurement gate	Y
81	51	EVT_HF_BM_START	Vorbereitung Strahlgym.	Y
82	52	EVT_HF_BM_AMPH2	Start Ampl., Ph. Kav. 2 Strahlgym.	Y
83	53	EVT_HF_BM_FREQ2	Start Freq. Kav. 2 Strahlgym.	Y
84	54	EVT_HF_BM_AMPH12	Start Ampl., Ph. Kav. 1+2 Strahlgym.	Y
85	55	EVT_HF_BM_FREQ1	Start Freq. Kav. 1 Strahlgym.	Y
86	56	EVT_HF_BM_AMPH1	Start Ampl., Ph. Kav. 1 Strahlgym.	Y
87	57	EVT_TG_CLEAR	Clear Timinggenerator	Y
88	58	EVT_MQ_START1	Load Q-Kicker (1st shot)	Y
89	59	EVT_MQ_START2	Load Q-Kicker (2nd shot)	Y
90	5A	EVT_MQ_MESS	Trigger for Q-Wert measurement	Y
91	5B	EVT_INT_FLAT	Start of internal Flattop	Y
92	5C	EVT_DT_MESS	Trigger for DTML measurement	Y
93	5D	EVT_DX_MESS	Trigger for DX measurement	Y
94	5E	EVT_TG_SWITCH	Umschalten der TG synchronisation	Y
95	5F	EVT_START_LECROY	Start measurement with LeCroy	Y
96	60	EVT_GAP_POS_MESS	Messevent zwischen den Zyklen	N
97	61	EVT_GAP_TRA_MESS	Messevent zwischen den Zyklen	N
98	62	EVT_GAP_SCR_MESS	Messevent zwischen den Zyklen	N
99	63	EVT_GAP_DTS_MESS	Messevent für schnelle Trafos	N
100	64	EVT_SIS_TRANS1_ESR	First transmission complete to ESR	N
101	65	EVT_SIS_TRANS2_ESR	Second transmission complete to ESR	N
102	66	EVT_PREP_DIAGNOSE	...	Y
103	67	EVT_PREP_DG	Vorbereitung Gitterhardware	Y
104	68	EVT_DG_TRIGGER	Trigger Messung Gitterhardware	Y
105	69	EVT_KICK_READY	Ext. Synchronisat. für Kicker	Y
106	6A	EVT_KICK_GATE	Start externe Synchr. für Kicker	Y
107	6B	EVT_PREP_DTI	Entklemmung TK trafos SIS timing	Y
108	6C	EVT_INJ_READY	Einzelne Unilac-Injektion erfolgt	Y
109	6D	EVT_MHB	Multi-Harmonischer-Betrieb von GS00BE_S (SIS18)	Y
128	80	EVT_ESR_READY_1	ESR ready for beam transfer	N
129	81	EVT_ESR_READY_2	ESR ready for beam transfer	N
130	82	EVT_ESR_REQ_TO_SIS	ESR beam request to SIS	N
131	83	EVT_EIN1	ESR ????? 1	N
132	84	EVT_EIN2	ESR ????? 2	N
133	85	EVT_MAN1	ESR manipulation 1	N
134	86	EVT_MAN2	ESR manipulation 2	N
135	87	EVT_PHASE_SYNCH_1	Phase is 1st time synchronized between ESR- and SIS-HF	N
136	88	EVT_PHASE_SYNCH_2	Phase is 2nd time synchronized between ESR- and SIS-HF	N
137	89	EVT_NO_BEAM	There is no beam in ESR (for diagnostics)	Y
138	8A	EVT_DT_STOP	Stop of DTML measurement	Y
139	8B	EVT_DT_READ	Read data for DTML measurement	Y
140	8C	EVT_DX_STOP	Stop of DX measurement	Y
141	8D	EVT_DX_READ	Read data for DX measurement	Y
142	8E	EVT_LEXT	ESR start with ?????????????	N
143	8F	EVT_PSTACK	ESR start with ?????????????	N
144	90	EVT_STACK	ESR start with ?????????????	N
145	91	EVT_ESR_TRANS_SIS	Transmission complete to SIS	N
146	92	EVT_ECE_HV_VAR	Stepwise variation of ECE voltage	Y
147	93	EVT_ECE_HV_ON	Write set value for pulsed ECE HV	Y
148	94	EVT_ECE_HV_MESS	Read actual value of pulsed ECE HV	Y
149	95	EVT_BUNCH_ROTATE	Start with bunch rotation	Y
150	96	EVT_ESR_REQ_REINJ	ESR request SIS reinjection	N
151	97	EVT_RESET	Start of 11th Ramp in magnets	Y
152	98	EVT_AUS1	Start of 11th Ramp in magnets	N
153	99	EVT_AUS2	Start of 11th Ramp in magnets	N
154	9A	EVT_RAMP_11	Start of 11th Ramp in magnets	N
155	9B	EVT_RAMP_12	Start of 12th Ramp in magnets	N
156	9C	EVT_RAMP_13	Start of 13th Ramp in magnets	N
157	9D	EVT_RAMP_14	Start of 14th Ramp in magnets	N
158	9E	EVT_RAMP_15	Start of 15th Ramp in magnets	N
159	9F	EVT_RAMP_16	Start of 16th Ramp in magnets	N
160	A0	EVT_EBEAM_ON	Electron beam on	Y
161	A1	EVT_EBEAM_OFF	Electron beam off	Y
162	A2	EVT_UDET_IN	Move detector (charge changed) in	Y
163	A3	EVT_UDET_OUT	Move detector out	Y
180	B4	EVT_TIMING_LOCAL	Take local timing	N
181	B5	EVT_TIMING_EXTERN	Switch to extern timing	N
199	C7	EVT_INTERNAL_FILL	PZ: Fill long event delays (>10s)	N
200	C8	EVT_DATA_START	First data transfer event	N
201	C9	EVT_DATA_0	Data transfer event	N
202	CA	EVT_DATA_1	Data transfer event	N
203	CB	EVT_DATA_2	Data transfer event	N
204	CC	EVT_DATA_3	Data transfer event	N
205	CD	EVT_DATA_4	Data transfer event	N
206	CE	EVT_DATA_5	Data transfer event	N
207	CF	EVT_DATA_6	Data transfer event	N
208	D0	EVT_DATA_7	Data transfer event	N
209	D1	EVT_TIME_1	Time stamp, most sign. bits	N
210	D2	EVT_TIME_2	Time stamp, medium sign. bits	N
211	D3	EVT_TIME_3	Time stamp, least sign. bits	N
224	E0	EVT_UTC_1	Time stamp UTC bits 32..39	N
225	E1	EVT_UTC_2	Time stamp UTC bits 24..31	N
226	E2	EVT_UTC_3	Time stamp UTC bits 16..23	N
227	E3	EVT_UTC_4	Time stamp UTC bits 8..15	N
228	E4	EVT_UTC_5	Time stamp UTC bits 0.. 7	N
245	F5	EVT_END_CMD_EXEC	End of command evaluation within gap	N
246	F6	EVT_BEGIN_CMD_EXEC	Start of command evaluation within gap	N
247	F7	EVT_GAP_INFO	PZ information about next cycle	N
248	F8	EVT_COLL_DET	PZ detected collision of 2 asynch. events	N
249	F9	EVT_TIMING_DIAG	For diagnostics in timing system	N
250	FA	EVT_SUP_CYCLE_START	Supercycle starts	N
251	FB	EVT_GET_EC_TIME	Synchronous reading of time of all ECs	N
252	FC	EVT_SET_EC_TIME	Synchronous setting of time in all ECs	N
253	FD	EVT_RESERVED	In older systems : change vrtacc event	N
254	FE	EVT_EMERGENCY	Emergency event	N
255	FF	EVT_COMMAND	Command event	Y
256	100	CMD_BP_START	Start of Beam Process	Y
257	101	CMD_SEQ_START	Sequence start. Implicitly, a CMD_SEQ_START is also a CMD_BP_START	Y
258	102	CMD_GAP_START	Start of gap window. Within this window, background tasks can be performed safely.	Y
259	103	CMD_GAP_END	End of gap window. Within this window, background tasks can be performed safely.	Y
270	10E	CMD_SOURCE_BEAM_ON	Source Beam On	Y
271	10F	CMD_SOURCE_BEAM_OFF	Source Beam Off	Y
272	110	CMD_SOURCE_HV_PREP	HV Preparation for the Source	Y
273	111	CMD_SOURCE_START	Start beam production in source	Y
274	112	CMD_SOURCE_STOP	Stop beam production in source and switch source to standby	Y
280	118	CMD_BI_TRIGGER	Beam Diagnostics: Trigger	Y
281	119	CMD_BI_MEAS1	Beam Diagnostics: Measure Event 1	Y
282	11A	CMD_BI_MEAS2	Beam Diagnostics: Measure Event 2	Y
283	11B	CMD_BEAM_INJECTION	Injection into a ring machine; played shortly prior to each injection within a sequence	Y
284	11C	CMD_BEAM_EXTRACTION	Extraction from a ring machine; played shortly prior to each extraction within a sequence	Y
285	11D	CMD_START_ENERGY_RAMP	Start acceleration or deceleration; only for beam-in processes; intended for diagnostic purposes	Y
286	11E	CMD_CUSTOM_DIAG_1	Intended for diagnostic purposes	Y
287	11F	CMD_CUSTOM_DIAG_2	Intended for diagnostic purposes	Y
288	120	CMD_CUSTOM_DIAG_3	Intended for diagnostic purposes	Y
290	122	CMD_RF_PREP	RF: Prepare device for pulse generation	Y
291	123	CMD_RF_PREP_PAUSE	RF: Prepare device for pulse generation (paused operation and beam-out)	Y
292	124	CMD_RF_STOP_PAUSE	RF: Stop generation of pulse (paused operation and beam-out)	Y
312	138	CMD_SYNCH	Trigger all function generators	Y
313	139	CMD_RF_SWITCH_01	Change RF system operation mode according to predefined settings	Y
314	13A	CMD_RF_SWITCH_02	Change RF system operation mode according to predefined settings	Y
315	13B	CMD_RF_SWITCH_03	Change RF system operation mode according to predefined settings	Y
316	13C	CMD_RF_SWITCH_04	Change RF system operation mode according to predefined settings	Y
317	13D	CMD_RF_SWITCH_05	Change RF system operation mode according to predefined settings	Y
318	13E	CMD_RF_SWITCH_06	Change RF system operation mode according to predefined settings	Y
319	13F	CMD_RF_SWITCH_07	Change RF system operation mode according to predefined settings	Y
320	140	CMD_RF_SWITCH_08	Change RF system operation mode according to predefined settings	Y
321	141	CMD_RF_SWITCH_09	Change RF system operation mode according to predefined settings	Y
322	142	CMD_RF_SWITCH_10	Change RF system operation mode according to predefined settings	Y
323	143	CMD_RF_SWITCH_11	Change RF system operation mode according to predefined settings	Y
324	144	CMD_RF_SWITCH_12	Change RF system operation mode according to predefined settings	Y
325	145	CMD_RF_SWITCH_13	Change RF system operation mode according to predefined settings	Y
326	146	CMD_RF_SWITCH_14	Change RF system operation mode according to predefined settings	Y
327	147	CMD_RF_SWITCH_15	Change RF system operation mode according to predefined settings	Y
328	148	CMD_RF_SWITCH_16	Change RF system operation mode according to predefined settings	Y
329	149	CMD_RF_SWITCH_17	Change RF system operation mode according to predefined settings	Y
330	14A	CMD_RF_SWITCH_18	Change RF system operation mode according to predefined settings	Y
331	14B	CMD_RF_SWITCH_19	Change RF system operation mode according to predefined settings	Y
332	14C	CMD_RF_SWITCH_20	Change RF system operation mode according to predefined settings	Y
333	14D	CMD_RF_SWITCH_21	Change RF system operation mode according to predefined settings	Y
334	14E	CMD_RF_SWITCH_22	Change RF system operation mode according to predefined settings	Y
335	14F	CMD_RF_SWITCH_23	Change RF system operation mode according to predefined settings	Y
336	150	CMD_RF_SWITCH_24	Change RF system operation mode according to predefined settings	Y
337	151	CMD_RF_SWITCH_25	Change RF system operation mode according to predefined settings	Y
338	152	CMD_RF_SWITCH_26	Change RF system operation mode according to predefined settings	Y
339	153	CMD_RF_SWITCH_27	Change RF system operation mode according to predefined settings	Y
340	154	CMD_RF_SWITCH_28	Change RF system operation mode according to predefined settings	Y
341	155	CMD_RF_SWITCH_29	Change RF system operation mode according to predefined settings	Y
342	156	CMD_RF_SWITCH_30	Change RF system operation mode according to predefined settings	Y
343	157	CMD_RF_SWITCH_31	Change RF system operation mode according to predefined settings	Y
344	158	CMD_RF_SWITCH_32	Change RF system operation mode according to predefined settings	Y
345	159	CMD_RF_PHASE_RESET	Trigger the DDS phase reset for RF devices	Y
350	15E	CMD_UNI_TCREQ	Request UNILAC PZ to reserve the transfer channel	N
351	15F	CMD_UNI_TCREL	Request UNILAC PZ to release the transfer channel	N
352	160	CMD_UNI_BREQ	Request UNILAC PZ to deliver beam	N
353	161	CMD_UNI_BPREP	Request UNILAC PZ to prepare beam delivery	N
354	162	CMD_UNI_BREQ_NOWAIT	Request UNILAC PZ to deliver beam but without 'wait block' in Data Master schedule	N
512	200	CMD_FG_PREP	Prepare function generator	Y
513	201	CMD_FG_START	Start function generator	Y
518	206	CMD_BEAM_ON	General: Begin of beam passage	Y
520	208	CMD_BEAM_OFF	General: End of beam passage	Y
521	209	CMD_SEPTUM_CHARGE	Start septum ramp up	Y
522	20A	CMD_EBEAM_ON	Electron beam on	Y
523	20B	CMD_EBEAM_OFF	Electron beam off	Y
524	20C	CMD_STOCH_COOLING_ON	Stochastic cooling on	Y
525	20D	CMD_STOCH_COOLING_OFF	Stochastic cooling off	Y
526	20E	CMD_TARGET_ON	Enable target	Y
527	20F	CMD_TARGET_OFF	Disable target	Y
528	210	CMD_EXP_DAQ_START	Start experiment data acquisition	Y
529	211	CMD_EXP_DAQ_STOP	Stop experiment data acquisition	Y
530	212	CMD_EXP_DRIVE_IN	Move experiment actuators (detectors) to measurement position	Y
531	213	CMD_EXP_DRIVE_OUT	Move experiment actuators (detectors) to outside position (clear beam aperture)	Y
532	214	CMD_DRIVE_MOVE	Move timing-controlled actuators to new position	Y
539	21B	CMD_CHOPPER_CHARGE	Start energizing chopper	Y
1024	400	CMD_BUMPER_CHARGE	Start bumper magnet ramp up	Y
1025	401	CMD_BUMPER_START	Start bumper ramp down	Y
1026	402	CMD_INJ_KICKER_START	Start injection kicker	Y
1027	403	CMD_EXTR_KICKER_START	Start extraction kicker	Y
2048	800	CMD_B2B_PMEXT	B2B internal: request phase measurement (extraction)	N
2049	801	CMD_B2B_PMINJ	B2B internal: request phase measurement (injection)	N
2050	802	CMD_B2B_PREXT	B2B internal: send result of phase measurement (extraction)	N
2051	803	CMD_B2B_PRINJ	B2B internal: send result of phase measurement (injection)	N
2052	804	CMD_B2B_TRIGGEREXT	B2B: trigger kicker electronics (extraction)	Y
2053	805	CMD_B2B_TRIGGERINJ	B2B: trigger kicker electronics (injection)	Y
2054	806	CMD_B2B_DIAGKICKEXT	B2B: send result of kick diagnostic (extraction)	Y
2055	807	CMD_B2B_DIAGKICKINJ	B2B: send result of kick diagnostic (injection)	Y
2056	808	CMD_B2B_DIAGEXT	B2B internal: send result of optional diagnostic (extraction)	N
2057	809	CMD_B2B_DIAGINJ	B2B internal: send result of optional diagnostic (injection)	N
2058	80A	CMD_B2B_PSHIFTEXT	B2B internal: request phase shift at low-level rf (extraction)	N
2059	80B	CMD_B2B_PSHIFTINJ	B2B internal: request phase shift at low-level rf (injection)	N
2079	81F	CMD_B2B_START	Start B2B procedure	Y
3328	D00	CMD_DM_COMM_0	Data Master communication	N
3329	D01	CMD_DM_COMM_1	Data Master communication	N
3330	D02	CMD_DM_COMM_2	Data Master communication	N
3331	D03	CMD_DM_COMM_3	Data Master communication	N
3332	D04	CMD_DM_COMM_4	Data Master communication	N
3333	D05	CMD_DM_COMM_5	Data Master communication	N
3334	D06	CMD_DM_COMM_6	Data Master communication	N
3335	D07	CMD_DM_COMM_7	Data Master communication	N
3336	D08	CMD_DM_COMM_8	Data Master communication	N
3337	D09	CMD_DM_COMM_9	Data Master communication	N
3338	D0A	CMD_DM_COMM_10	Data Master communication	N
3339	D0B	CMD_DM_COMM_11	Data Master communication	N
3340	D0C	CMD_DM_COMM_12	Data Master communication	N
3341	D0D	CMD_DM_COMM_13	Data Master communication	N
3342	D0E	CMD_DM_COMM_14	Data Master communication	N
3343	D0F	CMD_DM_COMM_15	Data Master communication	N
3344	D10	CMD_DM_COMM_16	Data Master communication	N
3345	D11	CMD_DM_COMM_17	Data Master communication	N
3346	D12	CMD_DM_COMM_18	Data Master communication	N
3347	D13	CMD_DM_COMM_19	Data Master communication	N
3348	D14	CMD_DM_COMM_20	Data Master communication	N
3349	D15	CMD_DM_COMM_21	Data Master communication	N
3350	D16	CMD_DM_COMM_22	Data Master communication	N
3351	D17	CMD_DM_COMM_23	Data Master communication	N
3352	D18	CMD_DM_COMM_24	Data Master communication	N
3353	D19	CMD_DM_COMM_25	Data Master communication	N
3354	D1A	CMD_DM_COMM_26	Data Master communication	N
3355	D1B	CMD_DM_COMM_27	Data Master communication	N
3356	D1C	CMD_DM_COMM_28	Data Master communication	N
3357	D1D	CMD_DM_COMM_29	Data Master communication	N
3358	D1E	CMD_DM_COMM_30	Data Master communication	N
3359	D1F	CMD_DM_COMM_31	Data Master communication	N
3360	D20	CMD_DM_COMM_32	Data Master communication	N
3361	D21	CMD_DM_COMM_33	Data Master communication	N
3362	D22	CMD_DM_COMM_34	Data Master communication	N
3363	D23	CMD_DM_COMM_35	Data Master communication	N
3364	D24	CMD_DM_COMM_36	Data Master communication	N
3365	D25	CMD_DM_COMM_37	Data Master communication	N
3366	D26	CMD_DM_COMM_38	Data Master communication	N
3367	D27	CMD_DM_COMM_39	Data Master communication	N
3368	D28	CMD_DM_COMM_40	Data Master communication	N
3369	D29	CMD_DM_COMM_41	Data Master communication	N
3370	D2A	CMD_DM_COMM_42	Data Master communication	N
3371	D2B	CMD_DM_COMM_43	Data Master communication	N
3372	D2C	CMD_DM_COMM_44	Data Master communication	N
3373	D2D	CMD_DM_COMM_45	Data Master communication	N
3374	D2E	CMD_DM_COMM_46	Data Master communication	N
3375	D2F	CMD_DM_COMM_47	Data Master communication	N
3376	D30	CMD_DM_COMM_48	Data Master communication	N
3377	D31	CMD_DM_COMM_49	Data Master communication	N
3378	D32	CMD_DM_COMM_50	Data Master communication	N
3379	D33	CMD_DM_COMM_51	Data Master communication	N
3380	D34	CMD_DM_COMM_52	Data Master communication	N
3381	D35	CMD_DM_COMM_53	Data Master communication	N
3382	D36	CMD_DM_COMM_54	Data Master communication	N
3383	D37	CMD_DM_COMM_55	Data Master communication	N
3384	D38	CMD_DM_COMM_56	Data Master communication	N
3385	D39	CMD_DM_COMM_57	Data Master communication	N
3386	D3A	CMD_DM_COMM_58	Data Master communication	N
3387	D3B	CMD_DM_COMM_59	Data Master communication	N
3388	D3C	CMD_DM_COMM_60	Data Master communication	N
3389	D3D	CMD_DM_COMM_61	Data Master communication	N
3390	D3E	CMD_DM_COMM_62	Data Master communication	N
3391	D3F	CMD_DM_COMM_63	Data Master communication	N
3392	D40	CMD_DM_COMM_64	Data Master communication	N
3393	D41	CMD_DM_COMM_65	Data Master communication	N
3394	D42	CMD_DM_COMM_66	Data Master communication	N
3395	D43	CMD_DM_COMM_67	Data Master communication	N
3396	D44	CMD_DM_COMM_68	Data Master communication	N
3397	D45	CMD_DM_COMM_69	Data Master communication	N
3398	D46	CMD_DM_COMM_70	Data Master communication	N
3399	D47	CMD_DM_COMM_71	Data Master communication	N
3400	D48	CMD_DM_COMM_72	Data Master communication	N
3401	D49	CMD_DM_COMM_73	Data Master communication	N
3402	D4A	CMD_DM_COMM_74	Data Master communication	N
3403	D4B	CMD_DM_COMM_75	Data Master communication	N
3404	D4C	CMD_DM_COMM_76	Data Master communication	N
3405	D4D	CMD_DM_COMM_77	Data Master communication	N
3406	D4E	CMD_DM_COMM_78	Data Master communication	N
3407	D4F	CMD_DM_COMM_79	Data Master communication	N
3408	D50	CMD_DM_COMM_80	Data Master communication	N
3409	D51	CMD_DM_COMM_81	Data Master communication	N
3410	D52	CMD_DM_COMM_82	Data Master communication	N
3411	D53	CMD_DM_COMM_83	Data Master communication	N
3412	D54	CMD_DM_COMM_84	Data Master communication	N
3413	D55	CMD_DM_COMM_85	Data Master communication	N
3414	D56	CMD_DM_COMM_86	Data Master communication	N
3415	D57	CMD_DM_COMM_87	Data Master communication	N
3416	D58	CMD_DM_COMM_88	Data Master communication	N
3417	D59	CMD_DM_COMM_89	Data Master communication	N
3418	D5A	CMD_DM_COMM_90	Data Master communication	N
3419	D5B	CMD_DM_COMM_91	Data Master communication	N
3420	D5C	CMD_DM_COMM_92	Data Master communication	N
3421	D5D	CMD_DM_COMM_93	Data Master communication	N
3422	D5E	CMD_DM_COMM_94	Data Master communication	N
3423	D5F	CMD_DM_COMM_95	Data Master communication	N
3424	D60	CMD_DM_COMM_96	Data Master communication	N
3425	D61	CMD_DM_COMM_97	Data Master communication	N
3426	D62	CMD_DM_COMM_98	Data Master communication	N
3427	D63	CMD_DM_COMM_99	Data Master communication	N
3428	D64	CMD_DM_COMM_100	Data Master communication	N
3429	D65	CMD_DM_COMM_101	Data Master communication	N
3430	D66	CMD_DM_COMM_102	Data Master communication	N
3431	D67	CMD_DM_COMM_103	Data Master communication	N
3432	D68	CMD_DM_COMM_104	Data Master communication	N
3433	D69	CMD_DM_COMM_105	Data Master communication	N
3434	D6A	CMD_DM_COMM_106	Data Master communication	N
3435	D6B	CMD_DM_COMM_107	Data Master communication	N
3436	D6C	CMD_DM_COMM_108	Data Master communication	N
3437	D6D	CMD_DM_COMM_109	Data Master communication	N
3438	D6E	CMD_DM_COMM_110	Data Master communication	N
3439	D6F	CMD_DM_COMM_111	Data Master communication	N
3440	D70	CMD_DM_COMM_112	Data Master communication	N
3441	D71	CMD_DM_COMM_113	Data Master communication	N
3442	D72	CMD_DM_COMM_114	Data Master communication	N
3443	D73	CMD_DM_COMM_115	Data Master communication	N
3444	D74	CMD_DM_COMM_116	Data Master communication	N
3445	D75	CMD_DM_COMM_117	Data Master communication	N
3446	D76	CMD_DM_COMM_118	Data Master communication	N
3447	D77	CMD_DM_COMM_119	Data Master communication	N
3448	D78	CMD_DM_COMM_120	Data Master communication	N
3449	D79	CMD_DM_COMM_121	Data Master communication	N
3450	D7A	CMD_DM_COMM_122	Data Master communication	N
3451	D7B	CMD_DM_COMM_123	Data Master communication	N
3452	D7C	CMD_DM_COMM_124	Data Master communication	N
3453	D7D	CMD_DM_COMM_125	Data Master communication	N
3454	D7E	CMD_DM_COMM_126	Data Master communication	N
3455	D7F	CMD_DM_COMM_127	Data Master communication	N
3456	D80	CMD_DM_COMM_128	Data Master communication	N
3457	D81	CMD_DM_COMM_129	Data Master communication	N
3458	D82	CMD_DM_COMM_130	Data Master communication	N
3459	D83	CMD_DM_COMM_131	Data Master communication	N
3460	D84	CMD_DM_COMM_132	Data Master communication	N
3461	D85	CMD_DM_COMM_133	Data Master communication	N
3462	D86	CMD_DM_COMM_134	Data Master communication	N
3463	D87	CMD_DM_COMM_135	Data Master communication	N
3464	D88	CMD_DM_COMM_136	Data Master communication	N
3465	D89	CMD_DM_COMM_137	Data Master communication	N
3466	D8A	CMD_DM_COMM_138	Data Master communication	N
3467	D8B	CMD_DM_COMM_139	Data Master communication	N
3468	D8C	CMD_DM_COMM_140	Data Master communication	N
3469	D8D	CMD_DM_COMM_141	Data Master communication	N
3470	D8E	CMD_DM_COMM_142	Data Master communication	N
3471	D8F	CMD_DM_COMM_143	Data Master communication	N
3472	D90	CMD_DM_COMM_144	Data Master communication	N
3473	D91	CMD_DM_COMM_145	Data Master communication	N
3474	D92	CMD_DM_COMM_146	Data Master communication	N
3475	D93	CMD_DM_COMM_147	Data Master communication	N
3476	D94	CMD_DM_COMM_148	Data Master communication	N
3477	D95	CMD_DM_COMM_149	Data Master communication	N
3478	D96	CMD_DM_COMM_150	Data Master communication	N
3479	D97	CMD_DM_COMM_151	Data Master communication	N
3480	D98	CMD_DM_COMM_152	Data Master communication	N
3481	D99	CMD_DM_COMM_153	Data Master communication	N
3482	D9A	CMD_DM_COMM_154	Data Master communication	N
3483	D9B	CMD_DM_COMM_155	Data Master communication	N
3484	D9C	CMD_DM_COMM_156	Data Master communication	N
3485	D9D	CMD_DM_COMM_157	Data Master communication	N
3486	D9E	CMD_DM_COMM_158	Data Master communication	N
3487	D9F	CMD_DM_COMM_159	Data Master communication	N
3488	DA0	CMD_DM_COMM_160	Data Master communication	N
3489	DA1	CMD_DM_COMM_161	Data Master communication	N
3490	DA2	CMD_DM_COMM_162	Data Master communication	N
3491	DA3	CMD_DM_COMM_163	Data Master communication	N
3492	DA4	CMD_DM_COMM_164	Data Master communication	N
3493	DA5	CMD_DM_COMM_165	Data Master communication	N
3494	DA6	CMD_DM_COMM_166	Data Master communication	N
3495	DA7	CMD_DM_COMM_167	Data Master communication	N
3496	DA8	CMD_DM_COMM_168	Data Master communication	N
3497	DA9	CMD_DM_COMM_169	Data Master communication	N
3498	DAA	CMD_DM_COMM_170	Data Master communication	N
3499	DAB	CMD_DM_COMM_171	Data Master communication	N
3500	DAC	CMD_DM_COMM_172	Data Master communication	N
3501	DAD	CMD_DM_COMM_173	Data Master communication	N
3502	DAE	CMD_DM_COMM_174	Data Master communication	N
3503	DAF	CMD_DM_COMM_175	Data Master communication	N
3504	DB0	CMD_DM_COMM_176	Data Master communication	N
3505	DB1	CMD_DM_COMM_177	Data Master communication	N
3506	DB2	CMD_DM_COMM_178	Data Master communication	N
3507	DB3	CMD_DM_COMM_179	Data Master communication	N
3508	DB4	CMD_DM_COMM_180	Data Master communication	N
3509	DB5	CMD_DM_COMM_181	Data Master communication	N
3510	DB6	CMD_DM_COMM_182	Data Master communication	N
3511	DB7	CMD_DM_COMM_183	Data Master communication	N
3512	DB8	CMD_DM_COMM_184	Data Master communication	N
3513	DB9	CMD_DM_COMM_185	Data Master communication	N
3514	DBA	CMD_DM_COMM_186	Data Master communication	N
3515	DBB	CMD_DM_COMM_187	Data Master communication	N
3516	DBC	CMD_DM_COMM_188	Data Master communication	N
3517	DBD	CMD_DM_COMM_189	Data Master communication	N
3518	DBE	CMD_DM_COMM_190	Data Master communication	N
3519	DBF	CMD_DM_COMM_191	Data Master communication	N
3520	DC0	CMD_DM_COMM_192	Data Master communication	N
3521	DC1	CMD_DM_COMM_193	Data Master communication	N
3522	DC2	CMD_DM_COMM_194	Data Master communication	N
3523	DC3	CMD_DM_COMM_195	Data Master communication	N
3524	DC4	CMD_DM_COMM_196	Data Master communication	N
3525	DC5	CMD_DM_COMM_197	Data Master communication	N
3526	DC6	CMD_DM_COMM_198	Data Master communication	N
3527	DC7	CMD_DM_COMM_199	Data Master communication	N
3528	DC8	CMD_DM_COMM_200	Data Master communication	N
3529	DC9	CMD_DM_COMM_201	Data Master communication	N
3530	DCA	CMD_DM_COMM_202	Data Master communication	N
3531	DCB	CMD_DM_COMM_203	Data Master communication	N
3532	DCC	CMD_DM_COMM_204	Data Master communication	N
3533	DCD	CMD_DM_COMM_205	Data Master communication	N
3534	DCE	CMD_DM_COMM_206	Data Master communication	N
3535	DCF	CMD_DM_COMM_207	Data Master communication	N
3536	DD0	CMD_DM_COMM_208	Data Master communication	N
3537	DD1	CMD_DM_COMM_209	Data Master communication	N
3538	DD2	CMD_DM_COMM_210	Data Master communication	N
3539	DD3	CMD_DM_COMM_211	Data Master communication	N
3540	DD4	CMD_DM_COMM_212	Data Master communication	N
3541	DD5	CMD_DM_COMM_213	Data Master communication	N
3542	DD6	CMD_DM_COMM_214	Data Master communication	N
3543	DD7	CMD_DM_COMM_215	Data Master communication	N
3544	DD8	CMD_DM_COMM_216	Data Master communication	N
3545	DD9	CMD_DM_COMM_217	Data Master communication	N
3546	DDA	CMD_DM_COMM_218	Data Master communication	N
3547	DDB	CMD_DM_COMM_219	Data Master communication	N
3548	DDC	CMD_DM_COMM_220	Data Master communication	N
3549	DDD	CMD_DM_COMM_221	Data Master communication	N
3550	DDE	CMD_DM_COMM_222	Data Master communication	N
3551	DDF	CMD_DM_COMM_223	Data Master communication	N
3552	DE0	CMD_DM_COMM_224	Data Master communication	N
3553	DE1	CMD_DM_COMM_225	Data Master communication	N
3554	DE2	CMD_DM_COMM_226	Data Master communication	N
3555	DE3	CMD_DM_COMM_227	Data Master communication	N
3556	DE4	CMD_DM_COMM_228	Data Master communication	N
3557	DE5	CMD_DM_COMM_229	Data Master communication	N
3558	DE6	CMD_DM_COMM_230	Data Master communication	N
3559	DE7	CMD_DM_COMM_231	Data Master communication	N
3560	DE8	CMD_DM_COMM_232	Data Master communication	N
3561	DE9	CMD_DM_COMM_233	Data Master communication	N
3562	DEA	CMD_DM_COMM_234	Data Master communication	N
3563	DEB	CMD_DM_COMM_235	Data Master communication	N
3564	DEC	CMD_DM_COMM_236	Data Master communication	N
3565	DED	CMD_DM_COMM_237	Data Master communication	N
3566	DEE	CMD_DM_COMM_238	Data Master communication	N
3567	DEF	CMD_DM_COMM_239	Data Master communication	N
3568	DF0	CMD_DM_COMM_240	Data Master communication	N
3569	DF1	CMD_DM_COMM_241	Data Master communication	N
3570	DF2	CMD_DM_COMM_242	Data Master communication	N
3571	DF3	CMD_DM_COMM_243	Data Master communication	N
3572	DF4	CMD_DM_COMM_244	Data Master communication	N
3573	DF5	CMD_DM_COMM_245	Data Master communication	N
3574	DF6	CMD_DM_COMM_246	Data Master communication	N
3575	DF7	CMD_DM_COMM_247	Data Master communication	N
3576	DF8	CMD_DM_COMM_248	Data Master communication	N
3577	DF9	CMD_DM_COMM_249	Data Master communication	N
3578	DFA	CMD_DM_COMM_250	Data Master communication	N
3579	DFB	CMD_DM_COMM_251	Data Master communication	N
3580	DFC	CMD_DM_COMM_252	Data Master communication	N
3581	DFD	CMD_DM_COMM_253	Data Master communication	N
3582	DFE	CMD_DM_COMM_254	Data Master communication	N
3583	DFF	CMD_DM_COMM_255	Data Master communication	N
4000	FA0	CMD_GMT_INTERNAL1	internal use by the GMT	N
4032	FC0	CMD_UNI_F50DM	Start of UNILAC 50Hz cycle (sent by Data Master)	N
4033	FC1	CMD_UNI_F50TUNE	Tune Data Master 50 Hz cycle length (sent by WR-F50 SCU, 1000us after 50 Hz mains trigger signal)	N

Table 1: Event numbers distributed by the timing system. The table has been extracted from the ACC database on 2025-Apr-04.

-- DietrichBeck - 04 April 2025