HadCon2 Multipurpose Controls Protocol Cmnd Apfel

Introduction

Api Basic Operation Principle

• HadCon 2 Multipurpose Controls Api Basic Operation

---

General Operation

The APFEL command set allows to talk to (several instances of) the APFEL ASIC. It uses a subset of the the I/O-Ports of the ATMEL μController to facilitate the communication to the proprietary protocol (q.v.Decoder.pdf) of the asic, sending a 22bit sequence for command, value, and chipId. ( → Apfel protocol code sequences)
• Logically
  • Output:
    • CLK
      • quasi clock, only the level changes are important
    • DOUT
      • data out
    • Side Select
      • position
  • Input:
    • DIN
      • data in
  • GND
• Electrical:
  • 3.3 Volt
• Physically:
  • per default:
    • JDINOUT1/2, JADC
      • I/O ports:
        

        I/O port	A		C		F
        Connector	JDINOUT1		JDINOUT2		JADC
        pins	DIN1	1	DIN1	1	DIN1	1
        	DOUT1	2	DOUT1	2	DOUT1	2
        	CLK1	3	CLK1	3	CLK1	3
        	SS1	4	SS1	4	SS1	4
        	DIN2	5	DIN2	5	DIN2	5
        	DOUT2	6	DOUT2	6	DOUT2	6
        	CLK2	7	CLK2	7	CLK2	7
        	SS2	8	SS2	8	SS2	8

---

Version 0

In the run of development an intermediate short command set has been implemented which is not so well descriptive as its future successor

edit

Commands

task	command	individual arguments	common address arguments	comment
setDac	APFEL 9 <DAC value> <dac> <chipId> <pinSetId> <sideSelectId> <port> [<quiet>] answer (if not quiet): → readDac	<DAC value> [ 0 ... 0x3FF ] <DAC> [ 1 ... 4 ]	<chipId> [ 0 ... 7, 8 ... FE, FF] 0xFF: generic call to all available chip Ids <pinSetId> [ 1, 2 ] <sideSelectId> [ 0,1 ] <port> A,C,F <quiet> [0,1]	writes DAC channel
readDac	APFEL A <dac> <chipId> <pinSetId> <sideSelectId> <port> answers: RECV APFEL dac <port> <pinSetId> <sideSelectId> <chipId> <dac> <DAC value> ERRA APFEL dac <port> <pinSetId> <sideSelectId> <chipId> <dac> <DAC value> - read validity check failed, raw value:	<DAC> [ 1 ... 4 ]		reads single DAC channel
readAllDacs	APFEL A 0  <chipId> <pinSetId> <sideSelectId> <port> answers: RECV APFEL dac <port> <pinSetId> <sideSelectId> <chipId> 0 <DAC value1> <DAC value2> <DAC value3> <DAC value4> ERRA APFEL dac <port> <pinSetId> <sideSelectId> <chipId> <dac> <DAC value> - read validity check failed, raw value:			*Not Yet Available* reads all DAC channels of an ch
autocalib	APFEL B <chipId> <pinSetId> <sideSelectId> <port>		auto calibration
TP single	APFEL C <pulse height Pattern> <chipId> <pinSetId> <sideSelectId> <port>	<pulse height Pattern> [ 2...3FF ]	test pulse
TP reset	APFEL D <pulse height> <channel> <chipId> <pinSetId> <sideSelectId> <port>	<pulse height Pattern> [ 1 ... F ] <channel> [ 1, 2 ]	test pulse inkl. reset
TP trigger	APFEL 11 <on/off> <port> <pin> <trigger position>	<on/off> [ 0,1 ] <port> [ A,B,C,D,E,F,G ] <pin> [1...8] <trigger after set (1) or after reset (2)> [1,2]		<on/off> enables/disables <pin> on <port> to trigger right in the moment after a test pulse set or reset command sequence is sent
setAmpl	APFEL E <channel> <chipId> <pinSetId> <sideSelectId> <port>	<channel> [ 1, 2 ]	setAmplification to high
resetAmpl	APFEL F <channel> <chipId> <pinSetId> <sideSelectId> <port>	<channel> [ 1, 2 ]	resetAmplification to low
listId	APFEL 10 <all> <NChipIds> <pinSetId> <sideSelectId> <port>	<all flag> [ 1...FF ] <number of chip Ids> [ 1...FF ]	check <number of chip Ids> channels and list depending on the <all flag> all or only positive results
listId++	APFEL 20 <all> <NChipIds> <minChipId> <pinSetId> <sideSelectId> <port>	<all flag> [ 1...FF ] <number of chip Ids> [ 1...FF ] <min Chip Id> [ 1...FF ]	check <number of chip Ids> channels and list depending on the <all flag> all or only positive results

---

---

First Test Results (16 Jan 2015)

Show ... (Expand all... Collapse all)Hide ... (Expand all... Collapse all)

edit

First Test Results from 16 Jan 2015

• programm uses inline functions.

  		typical	best measured	"preHadCon2 Timings" ~× 8000
  Clock Timing	T [µs]	44.8	24.8	400,000
  	f [kHz]	22.3	40.3	0.0027
  Function call overhead offset	[µs]	~330	~300
  Task Timings
  Task		typical	best measured
  set DAC	[ms]	2.4	1.4
  read DAC	[ms]	2.7	1.6
  AutoCalibration	[ms]	48.4	27
  AutoCalibration × 256 × 2	[s]	24.8	13.8
  TestPulseSequence	[ms]	2.3	1.4
  TestPulse	[ms]	4.7	2.7
  SetAmplitude	[ms]	2.3	1.3
  ResetAmplitude	[ms]	2.3	1.3

Original Notes

---

Logic Analyzer Results (14 Oct 2015)

Show ... (Expand all... Collapse all)Hide ... (Expand all... Collapse all)

edit

Logic Analyzer Results

Summary (10 Oct 2015)

		typical	"preHadCon2 Timings" ~× 104
Clock Timing	T [µs]	40	400,000
	f [kHz]	25 kHz	0.0027
Function call overhead offset	[µs]	~330
Task Timings
Task		typical
set DAC w/o readback	[ms]	2
read DAC	[ms]	2.3
set DAC w/ readback (estimate)	[ms]	4.3
AutoCalibration	[ms]	~155
AutoCalibration × 256 × 2 (estimate)	[s]	~80
TestPulseSequence	[ms]	2
complete TestPulse	[ms]	4
SetAmplitude	[ms]	2
ResetAmplitude	[ms]	2

---

Details (port A - 10 Oct 2015)

set DAC	APFEL 9 3FF 3 1 1 1 A 1	%FOREACH{"item" in="setDac_APFEL_9_3FF_3_1_1_1_A_1_2015-10-14.png"}% %NEXT{"item"}%
readDAC	APFEL A 3 1 1 1 A	%FOREACH{"item" in="readDac_APFEL_A_3_1_1_1_A_2015-10-14.png"}% %NEXT{"item"}%
autocalibration	APFEL B 1 1 1 A	%FOREACH{"item" in="autocalib_APFEL_B_1_1_1_A__2015-10-14.png"}% %NEXT{"item"}%
autocalibration (full)	APFEL B 1 1 1 A	%FOREACH{"item" in="autocalib_APFEL_B_1_1_1_A_(full)_2015-10-14.png"}% %NEXT{"item"}%
TP single	APFEL C 3 1 1 1 A	%FOREACH{"item" in="TP_single_APFEL_C_3_1_1_1_A_2015-10-14.png"}% %NEXT{"item"}%
TP reset ch1	APFEL D 9 1 1 1 1 A	%FOREACH{"item" in="TP_reset_APFEL_D_9_1_1_1_1_A_2015-10-14.png"}% %NEXT{"item"}%
TP reset ch2	APFEL D 9 2 1 1 1 A	%FOREACH{"item" in="TP_reset_APFEL_D_9_2_1_1_1_A_2015-10-14.png"}% %NEXT{"item"}%
TP reset ch1 incl. Trig, Pos 1	APFEL D 9 1 1 1 1 A	%FOREACH{"item" in="TP_reset_inkl_Trig_Pos_1_APFEL_D_9_1_1_1_1_A_2015-10-14.png"}% %NEXT{"item"}%
TP reset ch1 incl. Trig, Pos 2	APFEL D 9 1 1 1 1 A	%FOREACH{"item" in="TP_reset_inkl_Trig_Pos_2_APFEL_D_9_1_1_1_1_A_2015-10-14.png"}% %NEXT{"item"}%
set amplification	APFEL E 2 1 1 1 A	%FOREACH{"item" in="setAmplification_APFEL_E_2_1_1_1_A__2015-10-14.png"}% %NEXT{"item"}%
reset amplification	APFEL F 2 1 1 1 A	%FOREACH{"item" in="resetAmplification_APFEL_F_2_1_1_1_A_2015-10-14.png"}% %NEXT{"item"}%

Details (port F - 06 Nov 2015)

Trigger Level at 2.0V

set DAC	APFEL 9 3FF 3 1 1 1 F 1	%FOREACH{"item" in="setDac_APFEL_9_3FF_3_1_1_1_F_1_2015-11-06.png"}% %NEXT{"item"}%
readDAC	APFEL A 3 1 1 0 F	%FOREACH{"item" in="readDac_APFEL_A_3_1_1_0_F_2015-11-06.png"}% %NEXT{"item"}%
autocalibration	APFEL B 1 1 1 F	%FOREACH{"item" in="autocalib_APFEL_B_1_1_1_F_2015-11-06.png"}% %NEXT{"item"}%
TP single	APFEL C 3 1 1 0 F	%FOREACH{"item" in="TP_single_APFEL_C_3_1_1_0_F_2015-11-06.png"}% %NEXT{"item"}%
TP reset ch2	APFEL D 9 2 1 1 1 F	%FOREACH{"item" in="TP_reset_APFEL_D_9_2_1_1_1_F_2015-11-06.png"}% %NEXT{"item"}%
set amplification	APFEL E 2 1 1 0 F	%FOREACH{"item" in="setAmplification_APFEL_E_2_1_1_0_F_2015-11-06.png"}% %NEXT{"item"}%
reset amplification	APFEL F 2 1 1 1 F	%FOREACH{"item" in="resetAmplification_APFEL_F_2_1_1_1_F_2015-11-06.png"}% %NEXT{"item"}%

---

Version 1

not yet implemented, but you may have a look ...
Show ... (Expand all... Collapse all)Hide ... (Expand all... Collapse all)

edit

%FOREACH{"ADDRESS" in="<portLetter> <portIndex> <sideSelectionId> <chipId>"}% %FOREACH{"CMND" in="APFEL"}%

Overview

overall main command structure:
$CMND <command> $ADDRESS  [<Argument(s)>]

command	address			arguments		comment
				"channel"	value(s)
dac	<portLetter> A,C,F,	<pinSetId> [ 1, 2 ]	<sideSelectId> [ 1, 2 ]	<chipId> [ 0 ... 7, 8 ... FE, FF] 0xFF: generic call to all available chip Ids see command chipIdIgnoreMask for limiting the chipId range	<dacId> [ 1 ... 4 ] < 4, e.g. 0xA: all DACs get value vDAC1	[vDAC1[vDAC2[vDAC3[vDAC4]]]] [ 0 ... 0x3FF ]	read/writes up to 4 DAC channels (if set with sign, incr/decr relatively)
autoCalib						auto calibration of the DAC channels
testPulse				<channelId> [ 1 ... 2 ] < 4, e.g. 0xA: both channels	height1 [height2] [ 0 ... 0xF ]	initiate test pulse
ampl				<channelId> [ 1 ... 2 ] < 4, e.g. 0xA: both channels	[ amplification1 [amplification2] ] [ 0,1, H,L ] 0,L: low amplification (× 16) 1,H: high amplification (× 32)	get/set amplification mode
l/list						lists all addresses of available ids

---

%FOREACH{"command" in="dac"}% %FOREACH{"alternative" in="d"}%

$CMND $alternative/$command

Task

Format

• NOTE: setting <chipId> to 0xFF loops over all avaiable chip IDs
• read
  • single DAC at port/pos/chipId:
    $CMND $command $ADDRESS <dacId>
    
  • all 4 DACs at port/pos/chipId:
    $CMND $command $ADDRESS
    
  • all 4 DACs of all available chipIds at port/pos:
    $CMND $command <portId> <sideSelectId>
    
• write
  • single DAC at port/pos/chipIds:
    $CMND $command $ADDRESS <dacId ≤ 4 > <value>
    
  • all 4 DACs at port/pos/chipId with same value:
    $CMND $command $ADDRESS <dacId > 4> <value>
    
  • all 4 DACs at port/pos/chipId with individual values:
    $CMND $command $ADDRESS <(dummy)> <valueDAC1> <valueDAC2> <valueDAC3> <valueDAC4>
    

Response

• single dac channel access
  
  RECV $CMND $command $ADDRESS <dacId> <value>
• any other plots per found chip
  
  RECV $CMND $command $ADDRESS <dacId> <valueDAC1> <valueDAC2> <valueDAC3> <valueDAC4>

Description


read or write values from/to DAC channel(s) (if set with sign, incr/decr relatively)

Arguments

• <portId>
• <posId>
• <chipId>
• <dacId>
• <value>

Comments

• see cim/chipIdIgnoreMask

--- %NEXT{"alternative"}%%NEXT{"command"}%

%FOREACH{"command" in="autocalib"}% %FOREACH{"alternative" in="a"}%

$CMND $alternative/$command

Task

Format

Response

Description

Comments

--- %NEXT{"alternative"}%%NEXT{"command"}%

%FOREACH{"command" in="testPulse"}% %FOREACH{"alternative" in="t"}%

$CMND $alternative/$command

Task

Format

Response

Description

Comments

--- %NEXT{"alternative"}%%NEXT{"command"}%

%FOREACH{"command" in="ampl"}%

$CMND $command

Task

Format

Response

Description

Comments

--- %NEXT{"command"}%

%FOREACH{"command" in="list"}% %FOREACH{"alternative" in="l"}%

$CMND $alternative/$command

Task

Format

Response

Description

Comments

--- %NEXT{"alternative"}%%NEXT{"command"}%

---

%NEXT{"CMND"}% %NEXT{"ADDRESS"}%

---

• apfel.tar.gz: Shell scripts used for testing the basic functionality before implementation
• Decoder.pdf: Apfel decode version 1_4

I	Attachment	Action	Size	Date	Who	Comment
pdf	Decoder.pdf	manage	812 K	2015-03-26 - 14:22	PeterZumbruch	Apfel decode version 1_4
gz	apfel.tar.gz	manage	33 K	2014-05-06 - 10:35	PeterZumbruch	Shell scripts used for testing the basic functionality before APWI implementation

Copyright © by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding GSI Wiki? Send feedback | Legal notice | Privacy Policy (german)