Epics@GSI Webhome

HadCon2 Multipurpose Controls Protocol Cmnd Apfel V0

Commands
task command individual arguments common address arguments comment
setDac APFEL 9 <DAC value> <dac> <chipId> <pinSetId> <sideSelectId> <port> [<quiet>]
answer (if not quiet): → readDac
<DAC value>
[ 0 ... 0x3FF ]
<DAC>
[ 1 ... 4 ]
<chipId>
[ 0 ... 7, 8 ... FE, FF]
0xFF: generic call to all available chip Ids
<pinSetId>
[ 1, 2 ]
<sideSelectId>
[ 0,1 ]
<port>
A,C,F <quiet>
[0,1]
writes DAC channel
readDac APFEL A <dac> <chipId> <pinSetId> <sideSelectId> <port>
answers:
RECV APFEL dac <port> <pinSetId> <sideSelectId> <chipId> <dac> <DAC value>
ERRA APFEL dac <port> <pinSetId> <sideSelectId> <chipId> <dac> <DAC value> - read validity check failed, raw value:
<DAC>
[ 1 ... 4 ]
reads single DAC channel
readAllDacs APFEL A 0  <chipId> <pinSetId> <sideSelectId> <port>
answers:
RECV APFEL dac <port> <pinSetId> <sideSelectId> <chipId> 0 <DAC value1> <DAC value2> <DAC value3> <DAC value4>
ERRA APFEL dac <port> <pinSetId> <sideSelectId> <chipId> <dac> <DAC value> - read validity check failed, raw value:
  *Not Yet Available* reads all DAC channels of an ch

autocalib APFEL B <chipId> <pinSetId> <sideSelectId> <port>   auto calibration

TP single APFEL C <pulse height Pattern> <chipId> <pinSetId> <sideSelectId> <port> <pulse height Pattern>
[ 2...3FF ]
test pulse
TP reset APFEL D <pulse height> <channel> <chipId> <pinSetId> <sideSelectId> <port> <pulse height Pattern>
[ 1 ... F ]
<channel>
[ 1, 2 ]
test pulse inkl. reset
TP trigger APFEL 11 <on/off> <port> <pin> <trigger position> <on/off>
[ 0,1 ]
<port>
[ A,B,C,D,E,F,G ]
<pin>
[1...8]
<trigger after set (1) or after reset (2)>
[1,2]
  <on/off> enables/disables <pin> on <port> to trigger right in the moment after a test pulse set or reset command sequence is sent

setAmpl APFEL E <channel> <chipId> <pinSetId> <sideSelectId> <port> <channel>
[ 1, 2 ]
setAmplification to high
resetAmpl APFEL F <channel> <chipId> <pinSetId> <sideSelectId> <port> <channel>
[ 1, 2 ]
resetAmplification to low

listId APFEL 10 <all> <NChipIds> <pinSetId> <sideSelectId> <port> <all flag>
[ 1...FF ] <number of chip Ids>
[ 1...FF ]
check <number of chip Ids> channels and list depending on the <all flag> all or only positive results
listId++ APFEL 20 <all> <NChipIds> <minChipId> <pinSetId> <sideSelectId> <port> <all flag>
[ 1...FF ] <number of chip Ids>
[ 1...FF ] <min Chip Id>
[ 1...FF ]
check <number of chip Ids> channels and list depending on the <all flag> all or only positive results


--
PeterZumbruch - 27 May 2015
-- PeterZumbruch - 2020-11-09
Topic revision: r19 - 2020-11-09, PeterZumbruch - This page was cached on 2020-12-03 - 05:14.

This site is powered by FoswikiCopyright © by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding GSI Wiki? Send feedback | Imprint (german) | Privacy Policy (german)